Excellent Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)




Sterling Silver Crescent and Bead Earrings

Supplies Desired
3" 4 x 1 mm sterling silver rectangle wire
20-just one 'Λ* head pins
Two turquoise disc beads
A person Vi* 1.7 mm black hollow rubber tube
Two sterling silver ear wires
What suggestions would you give a commencing artist?
“Do Anything you adore. Investigate diverse media. Offer with a selective, limited, basis in the beginning to view what will work or what would not be just right for you before you jump into A significant outlay of money and effort.*
-Sally J. Phillips Jewelry Designer
Equipment Wanted
Ruler
Marker
Jeweler's observed or tin snips Protection Eyeglasses Hard, flat surface Awl
Hammer /is" drill bit
Hand held rotary Instrument, flex shaft, or drill press File
Fantastic grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers


1.Make use of the ruler to evaluate and mark two one Vi’ items of four x 1 mm rectangle sterling silver wire.
2Using a jeweler's saw or tin snips, cut the 4 x 1 mm rectangle sterling silver wire into two 1 Vi’ lengths.
3.File Every stop of the 1Vi" rectangle wire pieces to remove any burs or rough edges.
If preferred, You can utilize the file to round the ends in the rectangle wire items. Make use of a fantastic grit sanding pad to go above the realm where you have filed to easy the perimeters and remove any file marks.
4.Use the ruler to measure and mark /*." from 1 finish from the 1 Vi’ pieces of rectangle wire and place a mark in the center of the wire. This is when you will drill the holes to slip The pinnacle pins as a result of.
five.Set on your own basic safety Eyeglasses!!! Area the 1 Vi" rectangle wire items onto a hard, flat surface. Place the point of your awl over the mark that you choose to built Vm,' from a person close with the rectangle wire parts, and firmly strike after on the highest on the awl using a hammer. This can mens ring make a pilot hole for drilling holes into the rectangle wire.

Sterling Silver Crescent and Men's Rings Bead Earrings
Chapter five

six.Employing a /is" drill little bit. drill holes into one particular stop from Mens Ring the rectangle wire pieces with a handheld rotary Software, flex shaft, or drill push (when even now donning your security glasses!).
7.Utilize the file or high-quality grit sanding pad to remove any burs or rough edges left from drilling holes into the rectangle wire parts.
eight.Curve equally 1W items of rectangle wire into a “C" shape employing a ring mandrel and rawhide mallet. If you don't have a ring mandrel and rawhide mallet, use two pair of chain nose pliers. Holding a person set of pliers in Every single hand, grasp Each and every finish of the one Vi* rectangle wire piece Along with the pliers and gently bend the rectangle wire into a “C* shape. Review equally in the C-shaped rectangle wire parts and modify the curves so that they're very similar in si2e. Established these aside.
9.Utilize the ruler to evaluate and mark the rubber tube into four equal parts measuring Vm’ Every single. Use scissors to cut the rubber tube.
ten.Position the turquoise disc bead on to the head pin and add just one V·' bit of the rubber tube, location the head pin from the hole within the C-formed rectangle wire, and afterwards incorporate another V«" bit of rubber tube.

thirteen. Hold the head pin Along with the bead, rubber tube, along with the rectangle wire on it in one hand While using the wire you bent pointing toward you. Using the spherical nose pliers, grip the tip of the head pin wire that is definitely pointing toward you and roll it away from you (visualize turning the ignition essential to begin your automobile). Launch the pliers from the head pin wire.
At this stage, the opening while in the loop at the top of The pinnacle pin wire need to nonetheless be significant ample to slip the ear wire on. When you incorporate the ear wire, use the spherical nose pliers to grasp the loop of the head pin wire and roll it shut. You need to use the round nose or chain nose pliers to regulate the shape of the loop at the highest of the head pin if mens ring you might want to.
11. Use the ruler to evaluate and mark /(.’ over the best piece of the hollow rubber tube. With the wire cutters or tin snips, Slice the head pin wire Yu.’ higher than the very best of the hollow rubber tube.
twelve. Use the chain nose pliers to bend The pinnacle pin wire next to the Men's Rings best in the rubber tube in a ninety-degree angle.
fourteen. Repeat these steps for the 2nd earring.







 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Excellent Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)”

Leave a Reply

Gravatar